This thesis introduces a novel type of electrochemical microstructuring for 316L stainless steel. The microstructuring methods were developed as a basis for a drug eluting coronary stent system. Coronary stents are used in order to dilate narrowed arteries. In order to prevent inflammation reactions, which lead to an excessive proliferation of cells and thus to a renarrowing of the artery, the new generation of stents are coated with drugs. The aim of this thesis was to create three dimensional microstructures on the surface as a basis for drug coatings. The microstructures are supposed to provide a protection for the drug during the implantation process and, moreover, control the release of the drug by providing microdepots retaining a certain amount of the drug. It was found that suitable microstructures can be generated by a combined etching method comprising a first electrochemical grain boundary etching step followed by an isotropic etching step. The first step is performed with nitric acid and creates a microgrid of narrow grain boundary furrows. These furrows are hollowed out by a second etching step, carried out either with phosphoric acid, hydrochloric acid or oxalic acid. The generated structures were found to be superior or equal in terms of corrosion properties and cell proliferation behavior compared to conventional grit blasted stents. It was shown that the in vitro release behavior could be substantially decelerated, with up to three times more drug retention after the first week of release in comparison to grit blasted stents.
«
This thesis introduces a novel type of electrochemical microstructuring for 316L stainless steel. The microstructuring methods were developed as a basis for a drug eluting coronary stent system. Coronary stents are used in order to dilate narrowed arteries. In order to prevent inflammation reactions, which lead to an excessive proliferation of cells and thus to a renarrowing of the artery, the new generation of stents are coated with drugs. The aim of this thesis was to create three dimensional...
»
Übersetzte Kurzfassung:
Es wurde ein neues Verfahren zur Oberflächenmodifikation von biokompatiblem Edelstahl entwickelt, mit dem durch elektrochemische Ätzung Mikrostrukturen im Mikrometerbereich aus den intrinsischen Materialstrukturen erzeugt werden können. Das Verfahren dient als Basis für eine Medikamentenbeschichtung von Stützen für verengte Herzkranzgefässe (Stents). Ein großes Problem bei dieser Behandlung ist eine hohe Wiederverschlussrate, die durch Entzündungsreaktionen verursacht wird. Diese kann durch eine Beschichtung des Stents mit entzündungshemmenden Medikamenten verhindert werden. Mit Hilfe des Verfahrens werden in einem zweistufigen Ätzprozess Mikrokavitäten erzeugt, die in der Lage sind, eine gewisse Menge an Medikament aufzunehmen und verzögert freizusetzen. Es wurde nachgewiesen, dass die erzeugten Oberflächen in Hinblick auf in vitro Korrosions- und Zellbesiedelungseigenschaften besser oder gleichwertig zu konventionellen sandgestrahlten Oberflächen sind. Der in vitro Medikamenten Release konnte erheblich verzögert werden, die erzeugten Oberflächen wiesen nach einer Woche Release noch eine im Vergleich zu sandgestrahlten Stents bis zu drei mal höhere Menge an gespeichertem Medikament auf.
«
Es wurde ein neues Verfahren zur Oberflächenmodifikation von biokompatiblem Edelstahl entwickelt, mit dem durch elektrochemische Ätzung Mikrostrukturen im Mikrometerbereich aus den intrinsischen Materialstrukturen erzeugt werden können. Das Verfahren dient als Basis für eine Medikamentenbeschichtung von Stützen für verengte Herzkranzgefässe (Stents). Ein großes Problem bei dieser Behandlung ist eine hohe Wiederverschlussrate, die durch Entzündungsreaktionen verursacht wird. Diese kann durch eine...
»
Veröffentlichung:
Universitätsbibliothek der Technischen Universität München